Underfloor Heating Installation | Options & Installers | Nu-Heat

We design our systems to be quick and easy to fit and commission, even for someone new to underfloor heating installation.

How easy it is to install underfloor heating?

Very! Every Nu-Heat system is designed for an easy installation. You can expect to receive the highest quality components and a bespoke design – a service that is rated 9.8 out of 10 by installers.

Find a Nu-Heat Registered Installer

If you’re looking for an experienced plumbing and heating engineer for your wet underfloor heating installation, or someone to install a heat pump, we can help through our Registered Installer Network. Currently, we have over 200 experienced installers signed up across the country.

Supporting your chosen installer

Already have a local plumbing and heating engineer in mind for your underfloor heating installation? We regularly offer support to both new and experienced installers. Your Account Manager is always to hand, along with our Technical Support Team, before, during and after your UFH installation.

See how underfloor heating is installed

Watch our short videos to see how some of our most popular underfloor heating systems are installed.

5 steps to installing ClipTrack^® screed underfloor heating:

Cover the insulation with a polythene protection layer to tank the room.
Fit the ClipTrack^®. This holds the heating tube at even spacing.
Push the UFH tube into the ClipTrack^® following the supplied design drawings.
Once the tube is connected back to the manifold, fill, flush and pressure test the system.
Pour the screed while the tube is under pressure.

UFH for new builds

Installing Screed Underfloor Heating

5 steps to installing LoPro^®Max retrofit underfloor heating:

Before getting started, check the floor is in a good condition and level before priming the area.
Lay the self-adhesive castellated panels directly over the existing floor (this must be structural).
Push the UFH tube into the panels following the supplied design drawings.
Once the tube is connected back to the manifold, fill, flush and pressure test the system.
Pour LoPro^®QuickSet, the specialist self-levelling compound that is supplied with the system, whilst the tube is under pressure. The compound dries quickly – in around eight hours – and floor coverings can be fitted after 72 hours.

UFH for renovations

Installing LoProMax Underfloor Heating

5 steps to installing LoPro^®10 retrofit underfloor heating:

Before getting started, check the floor is in a good condition and level before laying the gypsum boards.
Lay the gypsum boards in a brick bond pattern directly over the existing floor (this must be structural).
Glue the edges of the boards together to form a strong bond, and screw to the sub floor if laid over suspended timber or a floating floor.
Prime the floor where castellated panels will sit, then follow the tube layout drawings to install the underfloor heating tube.
Once the tube is connected back to the manifold, fill, flush and pressure test the system.
Pour LoPro^®QuickSet, the specialist self-levelling compound that is supplied with the system, over the castellated panel whilst the tube is under pressure. The compound dries quickly – in around eight hours – and floor coverings can be fitted after 72 hours.

Installing LoPro10 Underfloor Heating

5 steps to installing ClippaPlate^® underfloor heating:

Feed the UFH tube through pre-notched or drilled holes in the joists.
Fix the ClippaPlate^® to the floor deck. This can be done from below, between the joists, or from above, straddling the joists.
With the plates in place, push the heating tube into the lip of the plates.
Once the tube is connected back to the manifold, fill, flush and pressure test the system
The ceiling or floor deck can now be fitted.

UFH for first floors

Installing ClippaPlate Underfloor Heating

A Guide To Nu-Heat’s Underfloor Heating Range

Find out more about Nu-Heat’s underfloor heating range, the type of project each system is best suited to, and how they are installed.

Watch the video

A Guide To Nu-Heat’s Underfloor Heating Range

Meet a Nu-Heat underfloor heating installer

Lee, of Woodhatch Plumbing and Heating, has been a member of our experienced Registered Installer Network for over 10 years.

“The complete, bespoke package that Nu-Heat delivers is great. The design process, literature and the people we deal with day-to-day are superb.

The Technical Support Team is always there for me to tap into, as well as giving support to my customers during and after the underfloor heating installation.

I know that I can handover the user instructions and design drawings to the end user and they will find it easy to understand and use their new heating system.

Knowing that Nu-Heat provides all that I need cuts out the headaches for me. It’s a cracking company!”.

Find an installer near you

Want help finding the right underfloor heating solution?

We would love to speak with you to discuss your project. If you have a question about your existing Nu-Heat system, our technical support team are at hand.