01404 549770 Get a free quote

Get expert advice about your project, contact us.

Filter systems

Project type
Floor Level
Floor type
Floor height build-up

Underfloor Heating

Screed

A screed system is often the most popular and cost-effective way to install UFH in a new build or new extension. This option also works particularly well with a heat pump.
Screed underfloor heating
  • 40-65mm build up
  • High heat output
  • Wet install

Screed

A screed system is often the most popular and cost-effective way to install UFH in a new build or new extension. This option also works particularly well with a heat pump.
Screed underfloor heating
  • 40-65mm build up
  • High heat output
  • Wet install
  • SC14: Hand laid screed with ClipTrack® securing 14mm heating tube.

    Data sheet View
    Installation sheet View
    Cross-section DWG
    3D DWG
  • SC17: Liquid or standard screed with ClipTrack® securing 17mm heating tube.

    Data sheet View
    Installation sheet View
  • SCB14: Hand laid screed between battens with ClipTrack® securing 14mm tube.

    Data sheet View
    Installation sheet View
  • SCS14: ClipTrack® securing 14mm tube for installation directly over an existing slab with insulation.

    Data sheet View
    Installation sheet View
  • SL14: Liquid screed with ClipTrack® securing 14mm heating tube.

    Data sheet View
    Installation sheet View
    Cross-section DWG
    3D DWG
  • SL17: Liquid or standard screed with ClipTrack® securing 17mm heating tube.

    Data sheet View
    Installation sheet View
  • SM14 & SMC14: Building mesh secures the 14mm heating tube.

    Data sheet View
    Installation sheet View
  • SP14: Fixing panel securing 14mm tube in screed.

    Data sheet View
    Installation sheet View
  • SPI14: Fixing panels with 10mm polystyrene backing securing the 14mm tube in screed.

    Data sheet View
    Installation sheet View

Found a good option? Contact our team to discuss your project.

LoPro® range

Made for renovations, the systems in the LoPro® range are low profile, offer high heat outputs and are simply laid over an existing floor for minimal disruption and maximum perfromance.
LoPro®Max underfloor heating
  • 15-26mm build up
  • Med-high heat output
  • Wet and dry install
  • LoPro®10: Pre-routed gypsum boards secure the 10mm tube.

    Data sheet View
    Installation sheet View
    Cross-section DWG
    3D DWG
  • LoPro®Lite: Pre-routed EPS boards with diffuser plates secure the 10mm tube.

    Data sheet View
    Installation sheet View
  • LoPro®Max: Castellated panel secures the 10mm tube before being covering in a specialist self-levelling compound.

    Data sheet View
    Installation sheet View
    Cross-section DWG
  • LoPro®Max14: Castellated panel secures the 14mm tube before being covering in a specialist self-levelling compound.

    Data sheet View

Found a good option? Contact our team to discuss your project.

Floating

Typically floated over the top of insulation, these systems are lightweight and eliminate the need for any wet trades. They require a deck to be fitted over the top, meaning they have a slightly higher build-up than the LoPro® range.
Floating underfloor heating
  • 22-34mm build up
  • High heat output
  • Dry install
  • DPB14: 14mm tube in low-profile diffuser panels installed between battens.

    Data sheet View
    Installation sheet View
    Cross-section DWG
  • DPBK14: 14mm tube in low-profile diffuser panels installed between battens with Knauf board.

    Data sheet View
    Installation sheet View
    Cross-section DWG
  • DPBL14: 14mm tube in low-profile diffuser panels installed between battens.

    Data sheet View
    Installation sheet DWG
    Cross-section DWG
  • DPBLK14: 14mm tube in low-profile diffuser panels installed between battens with Knauf board.

    Data sheet View
    Installation sheet View
    Cross-section DWG
  • DPF14: 14mm tube in low-profile diffuser panels.

    Data sheet View
    Installation sheet View
  • DPFK14: 14mm tube in low-profile diffuser panels with Knauf board.

    Data sheet View
    Cross-section DWG
  • DPL14: 14mm tube in low-profile diffuser panels in a floating floor.

    Data sheet View
    Installation sheet View
  • DPLK14: 14mm Fastflo® in low-profile diffuser panels in a floating floor, with Knauf board

    Data sheet View
    Installation sheet View
  • FDC14: Low-profile moulded FastDeck® panels with integrated foil-faced deck, installed on a concrete or beam & block slab.

    Data sheet View
    Installation sheet View
  • FDT14: Low-profile moulded FastDeck® panels with foil-faced deck, installed on a timber deck.

    Data sheet View
    Installation sheet View
  • TSB14: 14mm tube in a suspended timber floor between battens with screed assist.

    Data sheet View
    Installation sheet View

Found a good option? Contact our team to discuss your project.

Between joists

For projects where there is no room for any height build-up, you have the option of fitting UFH between joists. You just need sound joists that are at regular centres.
Joisted underfloor heating
  • 0-15mm build up
  • Med-high heat output
  • Dry install
  • DPJ14: 14mm tube in low-profile diffuser panels installed between first floor joists or battens.

    Data sheet View
    Cross-section DWG
    3D DWG
  • DPJG14: 14mm tube in low-profile diffuser panels installed between ground floor joists.

    Data sheet View
    Cross-section DWG
    3D DWG
  • DPJGK14: 14mm tube in low-profile diffuser panels installed between ground floor joists with Knauf board.

    Data sheet View
  • DPJK14: 14mm tube in low-profile diffuser panels installed between first floor joists with Knauf board.

    Data sheet View
  • TPBA14: Suspended timber upper floor with ClippaPlate® installed from above or below securing the 14mm tube.

    Data sheet View
    Installation sheet View
    Cross-section DWG
  • TPBAK14: As above but with the addition of Knauf board to boost heat output and aid acoustic performance.

    Data sheet View
    Installation sheet View
  • TS14: 14mm tube in a suspended timber floor with screed assist.

    Data sheet View
    Cross-section DWG
    3D DWG
  • TSG14: 14mm tube in a suspended timber floor between battens with screed assist.

    Data sheet View
    Cross-section DWG
    3D DWG

Found a good option? Contact our team to discuss your project.

OneZone®

OneZone® kits include everything you need to install a high-quality UFH system in one single area, whether a new extension, kitchen refurb or ensuite bathroom.
OneZone underfloor heating
  • 12-22mm build up
  • Med-high heat output
  • Wet and dry install
  • ElectroMat®: Nu-Heat’s electric UFH system. A popular option for smaller kitchens and bathrooms.

    Data sheet View
    Installation sheet View
  • LoPro®Lite: A lightweight and completely dry UFH system that uses pre-routed EPS boards with diffuser plates to secure the 10mm tube.

    Installation sheet View
  • LoPro®Max: A retrofit UFH system that uses castellated panels to hold the 10mm tube before being covered in a conductive self-levelling compound.

    Installation sheet View
  • Screed ClipTrack®: A traditional screen UFH system for new extensions.

    Installation sheet View

Found a good option? Contact our team to discuss your project.

Acoustic range

Acoustic UFH systems effectively reduce airborne and impact noise, as well as providing efficient heating altogether in one solution.
Acoustic underfloor heating
  • 0-65mm build up
  • Med-high heat output
  • Wet and dry install
  • AKA14: 14mm tube with ClippaPlate® in a resilient batten floor with Knauf board.

    Data sheet View
    Installation sheet View
  • ALPB10: Suspended timber joists with acoustic battens and pre-routed LoPro®10 panels securing the 10mm tube.

    Data sheet View
    Installation sheet View
  • ALPFC10: 10mm Fastflo® in pre-routed LoPro®10 panel in an acoustic floor on a concrete slab or beam & block sub-base

    Installation sheet View
    Cross-section DWG
    3D DWG
  • ALPRAF10: Raised access floor with 10mm tube in a pre-routed LoPro®10 panel in a raised access floor on a concrete slab.

    Data sheet View
    Installation sheet View
  • ALPRC10: Concrete slab or beam and block sub-base with pre-routed LoPro®10 panels securing the 10mm tube.

    Data sheet View
    Installation sheet View
  • ALPRT10: Suspended timber joists with pre-routed LoPro®10 panels securing the 10mm tube.

    Data sheet View
    Installation sheet View
  • ASC14: 14mm tube with ClipTrack® for acoustic sand and cement screed floors.

    Data sheet View
    Installation sheet View
  • ASCE14: 14mm tube for acoustic sand and cement screed floor with edge insulation.

    Data sheet View
    Installation sheet View
  • ASL14: 14mm tube with ClipTrack® for acoustic liquid screed floors.

    Data sheet View
  • ASLE14: 14mm tube with ClipTrack® for acoustic liquid screed floors with edge insulation.

    Data sheet View
  • AST14: 14mm tube with tacker panel for acoustic screed floors.

    Data sheet View
  • ATAC14: 14mm tube with ClippaPlate® installed in a resilient batten or resilient saddle system.

    Data sheet View
    Installation sheet View
  • ATAK14: 14mm tube with ClippaPlate® in an acoustic floor with Knauf board.

    Data sheet View
    Installation sheet View
  • ATPAK14: 14mm tube with ClippaPlate® in an acoustic floor with Knauf board.

    Data sheet View
    Installation sheet View

Found a good option? Contact our team to discuss your project.