Find the right UFH system for your project
Nu-Heat’s range of underfloor heating (UFH) can dramatically cut down on installation time and, with products and fixings for over 60 different floor constructions, is designed to work in all situations and across all scenarios.
Use our UFH selector tool to get a feel for what system would best suit your project, then speak to our team of experts to understand how it’ll work best for you.
Get expert advice about your project, contact us.
Filter systems
Screed
A screed system is often the most popular and cost-effective way to install UFH in a new build or new extension. This option also works particularly well with a heat pump.
- 40-65mm build up
- High heat output
- Wet install
LoPro® range
Made for renovations, the systems in the LoPro® range are low profile, offer high heat outputs and are simply laid over an existing floor for minimal disruption and maximum perfromance.
- 15-26mm build up
- Med-high heat output
- Wet and dry install
-
LoPro®10: Pre-routed gypsum boards secure the 10mm tube.
-
LoPro®Lite: Pre-routed EPS boards with diffuser plates secure the 10mm tube.
-
LoPro®Max: Castellated panel secures the 10mm tube before being covering in a specialist self-levelling compound.
-
LoPro®Max14: Castellated panel secures the 14mm tube before being covering in a specialist self-levelling compound.
Data sheet View
Found a good option? Contact our team to discuss your project.
OneZone®
OneZone® kits include everything you need to install a high-quality UFH system in one single area, whether a new extension, kitchen refurb or ensuite bathroom.
- 12-22mm build up
- Med-high heat output
- Wet and dry install
-
ElectroMat®: Nu-Heat’s electric UFH system. A popular option for smaller kitchens and bathrooms.
-
LoPro®Lite: A lightweight and completely dry UFH system that uses pre-routed EPS boards with diffuser plates to secure the 10mm tube.
Installation sheet View -
LoPro®Max: A retrofit UFH system that uses castellated panels to hold the 10mm tube before being covered in a conductive self-levelling compound.
Installation sheet View -
Screed ClipTrack®: A traditional screen UFH system for new extensions.
Installation sheet View
Found a good option? Contact our team to discuss your project.
Screed
A screed system is often the most popular and cost-effective way to install UFH in a new build or new extension. This option also works particularly well with a heat pump.
- 40-65mm build up
- High heat output
- Wet install
-
SC14: Hand laid screed with ClipTrack® securing 14mm heating tube.
-
SC17: Liquid or standard screed with ClipTrack® securing 17mm heating tube.
-
SCB14: Hand laid screed between battens with ClipTrack® securing 14mm tube.
-
SCS14: ClipTrack® securing 14mm tube for installation directly over an existing slab with insulation.
-
SL14: Liquid screed with ClipTrack® securing 14mm heating tube.
-
SL17: Liquid or standard screed with ClipTrack® securing 17mm heating tube.
-
SM14 & SMC14: Building mesh secures the 14mm heating tube.
-
SP14: Fixing panel securing 14mm tube in screed.
-
SPI14: Fixing panels with 10mm polystyrene backing securing the 14mm tube in screed.
Found a good option? Contact our team to discuss your project.
Underfloor Heating
Acoustic range
Acoustic UFH systems effectively reduce airborne and impact noise, as well as providing efficient heating altogether in one solution.
- 0-65mm build up
- Med-high heat output
- Wet and dry install
-
AKA14: 14mm tube with ClippaPlate® in a resilient batten floor with Knauf board.
-
ALPB10: Suspended timber joists with acoustic battens and pre-routed LoPro®10 panels securing the 10mm tube.
-
ALPFC10: 10mm Fastflo® in pre-routed LoPro®10 panel in an acoustic floor on a concrete slab or beam & block sub-base
-
ALPRAF10: Raised access floor with 10mm tube in a pre-routed LoPro®10 panel in a raised access floor on a concrete slab.
-
ALPRC10: Concrete slab or beam and block sub-base with pre-routed LoPro®10 panels securing the 10mm tube.
-
ALPRT10: Suspended timber joists with pre-routed LoPro®10 panels securing the 10mm tube.
-
ASC14: 14mm tube with ClipTrack® for acoustic sand and cement screed floors.
-
ASCE14: 14mm tube for acoustic sand and cement screed floor with edge insulation.
-
ASL14: 14mm tube with ClipTrack® for acoustic liquid screed floors.
Data sheet View -
ASLE14: 14mm tube with ClipTrack® for acoustic liquid screed floors with edge insulation.
Data sheet View -
AST14: 14mm tube with tacker panel for acoustic screed floors.
Data sheet View -
ATAC14: 14mm tube with ClippaPlate® installed in a resilient batten or resilient saddle system.
-
ATAK14: 14mm tube with ClippaPlate® in an acoustic floor with Knauf board.
-
ATPAK14: 14mm tube with ClippaPlate® in an acoustic floor with Knauf board.
Found a good option? Contact our team to discuss your project.
Suspended timber
For projects where there is very little height build-up, you have the option of fitting UFH between or on top of joists.
- 0-6mm build up
- Med-high heat output
- Dry install
-
DPJ14: 14mm tube in low-profile diffuser panels installed between first floor joists or battens.
-
DPJG14: 14mm tube in low-profile diffuser panels installed between ground floor joists.
-
DPJGK14: 14mm tube in low-profile diffuser panels installed between ground floor joists with Knauf board.
Data sheet View -
DPJK14: 14mm tube in low-profile diffuser panels installed between first floor joists with Knauf board.
Data sheet View -
Nu-Deck: An integrated structural underfloor heating system exclusively for suspended timber floors.
-
TPBA14: Suspended timber upper floor with ClippaPlate® installed from above or below securing the 14mm tube.
-
TPBAK14: As above but with the addition of Knauf board to boost heat output and aid acoustic performance.
-
TS14: 14mm tube in a suspended timber floor with screed assist.
-
TSG14: 14mm tube in a suspended timber floor between battens with screed assist.
Found a good option? Contact our team to discuss your project.
Floating
Typically floated over the top of insulation, these systems are lightweight and eliminate the need for any wet trades. They require a deck to be fitted over the top, meaning they have a slightly higher build-up than the LoPro® range.
- 22-34mm build up
- High heat output
- Dry install
-
DPB14: 14mm tube in low-profile diffuser panels installed between battens.
-
DPBK14: 14mm tube in low-profile diffuser panels installed between battens with Knauf board.
-
DPBL14: 14mm tube in low-profile diffuser panels installed between battens.
-
DPBLK14: 14mm tube in low-profile diffuser panels installed between battens with Knauf board.
-
DPF14: 14mm tube in low-profile diffuser panels.
-
DPFK14: 14mm tube in low-profile diffuser panels with Knauf board.
-
DPL14: 14mm tube in low-profile diffuser panels in a floating floor.
-
DPLK14: 14mm Fastflo® in low-profile diffuser panels in a floating floor, with Knauf board
-
FDC14: Low-profile moulded FastDeck® panels with integrated foil-faced deck, installed on a concrete or beam & block slab.
-
FDT14: Low-profile moulded FastDeck® panels with foil-faced deck, installed on a timber deck.
-
TSB14: 14mm tube in a suspended timber floor between battens with screed assist.
Found a good option? Contact our team to discuss your project.
We’re here to help you with your project
For expert advice on underfloor heating and renewables, contact us today.
